Tossing your faucet simply since it is leaky is wasteful and
expensive. Tons of brass, steel, silicone, chrome-plated plastic, and die-cast zinc
every year end up in garbage dumps due to
the fact that faucets are old and have reached the end of their life-spans. However many other tons are
needlessly disposed of due to leaks that property owners did not think could be repaired.
Hanging onto a leaky faucet is costly, too. The United States
Environmental Protection Agency approximates that the average U.S.
household wastes 9,400 gallons of water annually from
family leaks. This is enough to run 300 loads of laundry. Leaks alone account
for nearly one trillion gallons of wasted water across the U.S. each year.
Water is a progressively dwindling resource.
Considered that the month-to-month rate of water for
a typical U.S. household increased by 52% from 2010 to 2017, this is a
pushing concern that exceeds just a matter of an
annoying drip in the evening.
Be part of the solution by fixing your own leaky faucet, both
for your own sake and for the good of the earth. This article will assist you
repair any of the four many basic kinds of
home faucets. It might be simpler than you
assume, and it usually will be more
economical than buying a new faucet.
Before You Start Your Repair
Faucet repair uses relatively couple of tools, a number
of which you might already have on hand. Before you begin
your repair, you will wish to have all tools and materials nearby.
Tools and Products
Allen Wrenches (Hex Wrenches).
Clean Plastic Bin.
Egg Carton, Optional (ideally Styrofoam).
Numerous Cleaning Up Implements: Q-Tip, Scouring Pad, Fabric
Rags, Old Toothbrush.
Components Particular to Your Kind Of Faucet.
Preparation and Shut-Down Procedures.
Shut Water Off: Shut down water at the faucet.
Location Container: Put bucket below sink, near the supply of water lines. This will gather drips after you detach the
Disconnect Water: Turn off the two water supply lines
under the sink (cold and hot). Disconnect water system valve
to sink under the cabinet. Let water drain into bucket.
Close Drain: Close with stopper. Ensure that no parts drop the sink by
sealing the sink drain with a few strips of duct tape.
Safeguard Components: Use duct tape to plier jaws to prevent
scratching components. One great recommendation is
to cut off the fingers from an old set of gloves and slip the fingers onto the plier jaws. For the
ultimate in security, purchase soft-jaw pliers at your local hardware
Prepare Collection Area: Set out bin, towel, and optional egg carton next to
sink to help in parts removal. Styrofoam egg containers work best,
given that they are not affected by water.
Prepare Cleaning Products: Location distilled vinegar and cleaning
implements near bin to eliminate mineral deposits on parts.
How to Repair Leaky Compression Faucets.
The easiest and earliest kind of faucet, the compression faucet is
differentiated by its different hot and cold controls which
require you to turn them clockwise to turn off the water.
Time Allotted: 30 minutes.
Tools and Materials: Channellock-type pliers; flat-head and Phillips screwdrivers; replacement
washer; plumber's grease; O-ring (optional).
Eliminate the faucet handles with pliers and flat-head screwdriver.
Remove the screw that attaches the handles to the valve stem with your
Phillips head screwdriver.
Pull the handle up to remove it.
Get rid of valve stem assembly cover, then get rid of the assembly
With your soft pliers or wrench, eliminate the hex-nut section of the valve stem
assembly by turning nut counter-clockwise.
Unscrew the hex nut the rest of the way and remove.
Locate the stem washer, which will be located at the bottom of the valve assembly. It
may be worn down and in need of replacement.
Remove brass screw protecting the stem washer in place.
Clean the washer holder location with vinegar and toothbrush to eliminate mineral deposits.
Eliminate old washer and utilize this as your model for when you go to the
store for a replacement. If the O-ring appeared to be worn, you can replace this too.
Reassemble: press the brand-new washer into valve seat, then connect with the
brass screw and the brand-new or existing O-ring.
Coat with plumber's grease.
Reassemble rest of faucet assembly.
How to Fix Ceramic Disk Faucets.
Double-control ceramic disk faucets have separate cold and hot controls. The
device that begins and stops water flow is a cartridge
containing a pair of highly sleek ceramic
disks. In some cases, only one side of this assembly may be
leaking. Test this out by at the same time shutting down the
supply of water below the sink to see which side is
Time Allotted: 45 minutes.
Tools and Products: Pliers; flat-head screwdriver; replacement cartridges; plumber's grease; O-
Open the plastic or metal cover plate that covers the handles.
The faucet body is protected to the cartridge generally by a Phillips
head screw, though often by an Allen screw. Eliminate the
fastener and separate the faucet body from the cartridge stem.
Get rid of the locking nut with Channellock-type pliers. In some models, you
might also find a brass screw on top of the cartridge. If so, remove it and keep it, as you might need it when you install the new cartridge.
Move out the retaining clip (or locking ring) with pliers, then raise out the cartridge. Take the old
cartridge to a hardware store for a specific replacement.
Soak staying parts in vinegar, then brush off to get rid of deposits.
Reassemble the faucet in reverse. If you saved the brass screw from earlier and it is required,
install this now.
Turn on your water system. Test the system
How to Fix Single Cartridge (Sleeve) Faucets.
Cartridge faucets, frequently discovered in kitchen areas,
typically have a single lever that satisfies a wide,
round base. The lever brings up to start the water flow. Side to
side movement manages the cold and hot functions. The optional one-
for-one replacement of the self-contained cartridge suggests less fussing with
Time Allotted: 45 minutes.
Tools and Materials: Allen wrenches; screwdrivers; Channellock-style pliers;
cleaning products; replacement cartridge (optional, if existing cartridge can
not be cleaned up).
With your Allen wrenches, unscrew and loosen up the set screw, then remove the handle.
Raise the decorative cap straight off. These are generally
delicate, so beware. Use your hands, not pliers.
With pliers, thoroughly pry the cartridge loose and remove further by
hand. The cartridge will have seals on the bottom that you can pry out with the flat-head screwdriver.
With your cleaning implements, clean the seals and the location where the seals rest. To
do this, soak in vinegar and brush off deposits with a Q-tip or old toothbrush. If the
deposits do not free easily, buy a new cartridge.
With your screwdriver, remove the O-ring from the faucet, coat with
plumbing's grease by hand, then re-install in the faucet body.
Replace the cleaned old cartridge or new cartridge, tightening up with
the Channellock pliers.
Gently change the ornamental cap.
Re-install handle, tightening up the set screw with the Allen wrenches.910.
How to Protect Your Home From Leaky Faucets in Sun Valley
What if I don`t quickly attend to a leaky faucet? in Sun Valley