Tossing your faucet merely since it is leaking is wasteful and
costly. Tons of brass, steel, silicone, chrome-plated plastic, and die-cast zinc
each year end up in garbage dumps due to
the fact that faucets are old and have reached the end of their life
expectancies. However many other tons are
needlessly disposed of due to leaks that house
owners did not think could be repaired.
Hanging onto a leaking faucet is expensive, too. The United States
Environmental Protection Agency approximates that the average U.S.
family wastes 9,400 gallons of water annually from
household leaks. This suffices to run 300 loads of laundry. Leaks alone represent nearly one trillion gallons of wasted water throughout the U.S. per
Water is a progressively diminishing resource.
Considered that the monthly price of water for
a typical U.S. family increased by 52% from 2010 to 2017, this is a
pushing problem that surpasses simply a matter of a bothersome drip during the night.
Be part of the solution by repairing your own dripping faucet, both
for your own sake and for the good of the earth. This post will assist you
repair any of the four a lot of basic types of
household faucets. It may be simpler than you
expect, and it usually will be less costly than buying a new faucet.
Before You Begin Your Repair
Faucet repair utilizes reasonably couple of tools, much of which you may currently have on hand. Prior to you begin
your repair, you will want to have all tools and products nearby.
Tools and Products
Allen Wrenches (Hex Wrenches).
Clean Plastic Bin.
Egg Carton, Optional (preferably Styrofoam).
Different Cleaning Up Implements: Q-Tip, Scouring Pad, Cloth
Rags, Old Toothbrush.
Components Particular to Your Kind Of Faucet.
Preparation and Shut-Down Procedures.
Shut Water Off: Turn off water at the faucet.
Place Pail: Put container listed below sink, near the water
supply lines. This will collect drips after you detach the
Disconnect Water: Turn off the two water supply lines
under the sink (cold and hot). Disconnect water supply valve
to sink under the cabinet. Let water drain into container.
Close Drain: Close with stopper. Ensure that no parts fall down the sink by
sealing the sink drain with a couple of strips of duct tape.
Secure Components: Use duct tape to plier jaws to prevent
scratching components. One terrific recommendation is
to cut off the fingers from an old pair of gloves and slip the fingers onto the plier jaws. For the
ultimate in security, purchase soft-jaw pliers at your local hardware
Prepare Collection Area: Set out bin, towel, and optional egg container next to
sink to aid in parts removal. Styrofoam egg cartons work best,
given that they are not affected by water.
Prepare Cleaning Items: Place distilled vinegar and cleaning
implements near bin to get rid of mineral deposits on parts.
How to Repair Leaky Compression Faucets.
The simplest and oldest type of faucet, the compression faucet is
differentiated by its separate hot and cold controls which
require you to turn them clockwise to turn off the water.
Time Allotted: thirty minutes.
Tools and Products: Channellock-type pliers; flat-head and Phillips screwdrivers; replacement
washer; plumber's grease; O-ring (optional).
Remove the faucet handles with pliers and flat-head screwdriver.
Get rid of the screw that attaches the handles to the valve stem with your
Phillips head screwdriver.
Pull the handle up to remove it.
Eliminate valve stem assembly cover, then remove the assembly
With your soft pliers or wrench, remove the hex-nut area of the valve stem
assembly by turning nut counter-clockwise.
Unscrew the hex nut the rest of the way and remove.
Find the stem washer, which will be located at the bottom of the valve assembly. It
might be worn down and in need of replacement.
Get rid of brass screw protecting the stem washer in place.
Clean the washer holder area with vinegar and tooth brush to remove mineral deposits.
Get rid of old washer and use this as your model for when you go to the
store for a replacement. If the O-ring appeared to be worn, you can replace this too.
Reassemble: push the new washer into valve seat, then attach with the
brass screw and the brand-new or existing O-ring.
Coat with plumber's grease.
Reassemble rest of faucet assembly.
How to Fix Ceramic Disk Faucets.
Double-control ceramic disk faucets have separate cold and hot controls. The
device that begins and stops water circulation is a cartridge
including a set of highly refined ceramic
disks. Sometimes, only one side of this assembly might be
dripping. Test this out by alternately shutting down the
water supply below the sink to see which side is
Time Allotted: 45 minutes.
Tools and Materials: Pliers; flat-head screwdriver; replacement cartridges; plumber's grease; O-
Open the plastic or metal cover plate that covers the handles.
The faucet body is protected to the cartridge normally by a Phillips
head screw, though sometimes by an Allen screw. Remove the
fastener and separate the faucet body from the cartridge stem.
Remove the locking nut with Channellock-type pliers. In some models, you
may likewise find a brass screw on top of the cartridge. If so, remove it and hold
onto it, as you might need it when you install the new cartridge.
Slide out the retaining clip (or locking ring) with pliers, then lift out the cartridge. Take the old
cartridge to a hardware shop for an exact replacement.
Soak remaining parts in vinegar, then brush off to get rid of deposits.
Reassemble the faucet in reverse. If you saved the brass screw from earlier and it is needed,
install this now.
Turn on your water system. Test the system
How to Fix Single Cartridge (Sleeve) Faucets.
Cartridge faucets, often discovered in cooking areas,
typically have a single lever that meets a large,
cylindrical base. The lever brings up to start the water flow. Side to
side motion manages the cold and hot functions. The optional one-
for-one replacement of the self-contained cartridge implies less fussing with
Time Allotted: 45 minutes.
Tools and Materials: Allen wrenches; screwdrivers; Channellock-style pliers;
cleaning materials; replacement cartridge (optional, if existing cartridge can
not be cleaned up).
With your Allen wrenches, unscrew and loosen up the set screw, then eliminate the handle.
Raise the decorative cap straight off. These are usually
delicate, so be careful. Use your hands, not pliers.
With pliers, thoroughly pry the cartridge loose and eliminate even more by
hand. The cartridge will have seals on the bottom that you can pry out with the flat-head screwdriver.
With your cleansing implements, clean the seals and the location where the seals rest. To
do this, take in vinegar and brush off deposits with a Q-tip or old tooth brush. If the
deposits do not free quickly, acquire a new cartridge.
With your screwdriver, remove the O-ring from the faucet, coat with
plumbing's grease by hand, then re-install in the faucet body.
Replace the cleaned old cartridge or brand-new cartridge, tightening with
the Channellock pliers.
Gently change the decorative cap.
Re-install handle, tightening the set screw with the Allen wrenches.910.
8 Causes for a Leaky Faucet in Winnetka
How to Protect Your Home From Leaky Faucets in Winnetka