1. Disconnect the p-trap and the straight extension pipe.
Big channel-lock pliers or a monkey wrench job well to loosen up the nuts holding the pipelines with each other. When both links are totally free, eliminate the parts. You might wish to clean the horizontal drainpipe pipeline to get rid of any kind of possible blockage. (This is not required in brand-new construction.).
2. Detach the down drain.
Making use of big channel-lock pliers, detach the down drain originating from the sink and the connection that affixes it to the p-trap. When both links are complimentary, get rid of the parts.
3. Unscrew the huge nut.
Loosen the big nut that holds the strainer in position underneath the sink. Get rid of the strainer body.
4. Pry off the breeze ring as well as clean off the old plumbing professional’s putty.
Making use of a flathead screwdriver, loosen up the 3 screws on the installing setting up as well as pry off the snap ring. Clean off the old plumber’s putty that borders the side of the drainpipe opening.
5. Set up the new sink flange.
Area a 1/2″ rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange into the drainpipe opening and press it right into place. Putting a weight, such as your garbage disposal, in addition to the sink flange will help hold the sink flange in place while mounting it to the sink. To prevent scratching your sink or the flange, place a towel between the sink surface as well as the weight.
6. Mount gasket and also flanges.
From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in place.
7. Slip on the installing and also break rings.
Next, slip on the placing ring and break ring. Tighten up the three installing screws, alternately tightening up each screw a few turns at a time up until the placing assembly is equally as well as securely seated against all-time low of the sink.
8. Remove the dish washer ko plug.
If utilizing a dishwashing machine, you will require to tap out the dish washer knockout plug. Lay the garbage disposal on its side and also use a screwdriver as well as hammer to touch it out. Next, get rid of the loosened knockout plug from inside the garbage disposal.
9. Connect the electrical.
Hardwired Unit:.
Turn the garbage disposal over and also get rid of electrical cover plate. Take out cables. Put cable television adapter (not consisted of) and run electric cord through access hole on base of garbage disposal. Tighten cord connector. Press cords right into garbage disposal (do not displace cardboard shield) as well as replace electrical cover plate.
If you have a hardwired device and you’re looking to attach a cable, you will require a power cable package.
Corded Unit:.
For a garbage disposal with a factory-installed cable, merely connect in to the outlet under your sink after completing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the lower mounting ring up until all 3 tabs are secured into the installing assembly.
11. Put the discharge tube.
Place the discharge tube into the discharge coupler, after that glide the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drainpipe pipeline.
Turn the garbage disposal so that the discharge tube is aligned with the drainpipe catch. If the discharge tube is also long, cut off as a lot of television as required. If it is too brief, you can buy an expansion. If you are connecting the garbage disposal to a dish washer, it may be connected with an air gap. Use a hose pipe clamp to attach the drainpipe pipe to the dishwasher inlet.
13. Lock the garbage disposal in place.
Since whatever is installed and also in position, lock the garbage disposal to the sink installing setting up using the wrench that included the device. Put the Quiet Collar Sink Baffle right into the sink opening by pushing it into the sink until it snaps into place.
14. Test the garbage disposal.
Test for leaks at the sink flange, dish washer, tail-pipe and also placing assembly connections. Ultimately, activate the electric breaker to evaluate its operation. Appreciate your new garbage disposal!
How to Install a Garbage Disposal in Glendale