1. Detach the p-trap as well as the straight extension pipe.
Huge channel-lock pliers or a monkey wrench job well to loosen the nuts holding the pipes together. When both links are totally free, eliminate the components. You may want to clean up the horizontal drainpipe pipeline to remove any feasible blockage. (This is not necessary in new building.).
2. Disconnect the down drain.
Using large channel-lock pliers, disconnect the down drainpipe coming from the sink and also the connection that affixes it to the p-trap. When both links are free, eliminate the components.
3. Loosen the large nut.
Unscrew the large nut that holds the strainer in place underneath the sink. Get rid of the strainer body.
4. Tear off the snap ring and clean off the old plumbing professional’s putty.
Utilizing a flathead screwdriver, loosen the 3 screws on the installing assembly and pry off the breeze ring. Wipe the old plumber’s putty that surrounds the side of the drainpipe opening.
5. Mount the brand-new sink flange.
Location a 1/2″ rope of plumber’s putty around the drain opening in the sink. Go down the brand-new sink flange right into the drainpipe opening and press it right into place. Placing a weight, such as your garbage disposal, on top of the sink flange will assist hold the sink flange in place while mounting it to the sink. To avoid scraping your sink or the flange, position a towel between the sink surface area as well as the weight.
6. Set up gasket as well as flanges.
From under the sink, slide the fiber gasket, backup flange and installing flange over the sink flange. Hold these items in position.
7. Slip on the installing and break rings.
Next, slip on the mounting ring and also break ring. Tighten the three mounting screws, at the same time tightening up each screw a few turns at a time till the mounting setting up is evenly as well as firmly seated against the bottom of the sink.
8. Remove the dishwashing machine knockout plug.
If making use of a dishwasher, you will certainly require to touch out the dish washer knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver and also hammer to tap it out. Next off, get rid of the loosened knockout plug from inside the garbage disposal.
9. Link the electric.
Hardwired Device:.
Turn the garbage disposal over as well as remove electric cover plate. Pull out cables. Place cord connector (not included) as well as run electric cable television through accessibility hole on base of garbage disposal. Tighten up wire port. Push wires into garbage disposal (do not displace cardboard guard) and also change electrical cover plate.
If you have a hardwired unit and also you’re looking to connect a cable, you will certainly require a power cable package.
Corded Device:.
For a garbage disposal with a factory-installed cable, merely connect in to the outlet under your sink after completing the remainder of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by lining up the three placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the reduced installing ring until all 3 tabs are locked right into the mounting assembly.
11. Insert the discharge tube.
Place the discharge tube into the discharge coupler, after that glide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
12. Align the discharge tube with the drainpipe pipe.
Revolve the garbage disposal to make sure that the discharge tube is lined up with the drain catch. If the discharge tube is also long, removed as a lot of the tube as required. If it is as well brief, you can acquire an extension. If you are linking the garbage disposal to a dish washer, it might be linked through an air gap. Make use of a hose clamp to attach the drain pipe to the dishwashing machine inlet.
13. Lock the garbage disposal in place.
Since whatever is mounted as well as ready, lock the garbage disposal to the sink placing setting up using the wrench that came with the unit. Place the Quiet Collar Sink Baffle right into the sink opening by pressing it right into the sink up until it snaps right into location.
14. Check the garbage disposal.
Examination for leakages at the sink flange, dishwasher, tail-pipe and installing assembly links. Ultimately, switch on the electrical breaker to evaluate its procedure. Appreciate your brand-new garbage disposal!
Installing a Replacement Garbage Disposal in Tarzana
How to Choose a Garbage Disposal in Tarzana