1. Detach the p-trap and the straight extension pipe.
Huge channel-lock pliers or a pipe wrench job well to loosen up the nuts holding the pipes together. When both links are cost-free, eliminate the components. You may intend to clean the straight drainpipe pipe to get rid of any kind of feasible obstruction. (This is not necessary in brand-new building.).
2. Detach the down drainpipe.
Making use of huge channel-lock pliers, disconnect the down drain coming from the sink as well as the connection that attaches it to the p-trap. When both links are complimentary, eliminate the components.
3. Loosen the large nut.
Loosen the big nut that holds the strainer in position below the sink. Remove the strainer body.
4. Pry off the snap ring and wipe the old plumbing technician’s putty.
Using a flathead screwdriver, loosen the 3 screws on the placing assembly and also pry off the snap ring. Clean off the old plumbing’s putty that surrounds the side of the drain opening.
5. Install the brand-new sink flange.
Location a 1/2″ rope of plumbing technician’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange into the drain opening and also press it right into place. Placing a weight, such as your garbage disposal, on top of the sink flange will assist hold the sink flange in place while installing it to the sink. To stay clear of scraping your sink or the flange, position a towel between the sink surface as well as the weight.
6. Set up gasket and flanges.
From under the sink, slide the fiber gasket, backup flange and also placing flange over the sink flange. Hold these pieces in place.
7. Slip on the placing and also snap rings.
Next off, slip on the installing ring and also snap ring. Tighten up the 3 placing screws, alternately tightening up each screw a few turns at once till the mounting assembly is evenly and also tightly seated against all-time low of the sink.
8. Eliminate the dish washer knockout plug.
If using a dishwashing machine, you will certainly require to touch out the dishwashing machine knockout plug. Lay the garbage disposal on its side and also use a screwdriver as well as hammer to tap it out. Next, get rid of the loose ko plug from inside the garbage disposal.
9. Attach the electrical.
Turn the garbage disposal over and remove electric cover plate. Pull out cables. Insert wire port (not consisted of) as well as run electric cord with access opening on bottom of garbage disposal. Tighten up cable connector. Press cables right into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired system as well as you’re seeking to connect a cable, you will certainly require a power cord package.
For a garbage disposal with a factory-installed cable, simply plug in to the outlet under your sink after completing the rest of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the reduced installing ring up until all 3 tabs are secured into the placing assembly.
11. Place the discharge tube.
Place the discharge tube right into the discharge coupler, then glide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drain pipe.
Rotate the garbage disposal to ensure that the discharge tube is straightened with the drainpipe trap. If the discharge tube is as well long, removed as much of television as necessary. If it is also short, you can acquire an expansion. If you are attaching the garbage disposal to a dish washer, it may be attached with an air space. Utilize a hose pipe clamp to attach the drain pipe to the dish washer inlet.
13. Lock the garbage disposal in position.
Now that whatever is set up as well as in position, lock the garbage disposal to the sink placing assembly using the wrench that came with the system. Put the Quiet Collar Sink Baffle right into the sink opening by pressing it into the sink until it snaps right into area.
14. Evaluate the garbage disposal.
Examination for leakages at the sink flange, dishwashing machine, tail-pipe and also mounting setting up links. Finally, turn on the electrical breaker to check its procedure. Enjoy your new garbage disposal!
Garbage Disposal Installation in Van Nuys
How to Install a Garbage Disposal in Van Nuys