05 Feb. 21

Installing a Replacement Garbage Disposal in Hidden Hills

1. Shut off power to the garbage disposal and also detach the down catch.
Shut off the electrical power at the circuit box or circuit breaker. Then, utilizing adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand and also put completion of the wrenchette or screwdriver right into the right side of one mounting lug on the lower installing ring. Raise the garbage disposal somewhat and loosen the lower placing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is without the mounting setting up.
3. Separate the electric.
Lay the garbage disposal on its side as well as get rid of the electric cover plate from the bottom. Loosen up the environment-friendly ground screw as well as eliminate wire ports. Separate garbage disposal cables from electrical supply wires. Loosen screws on the electric clamp port and also remove cords from the garbage disposal.

4. Eliminate existing installing equipment if equipment replacement needed. Otherwise miss to step 12.
To get rid of the existing installing hardware, loosen the three installing screws, tear the breeze ring off with a screwdriver as well as remove the old placing setting up.

5. Get rid of the old sink flange as well as putty.
Push the old sink flange up with the sink opening. Utilize a screwdriver or putty blade to meticulously scuff all old putty from the side of the sink opening
. Set up the brand-new sink flange, gasket and rings.
Place a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange right into the drain opening and also press it right into location. Putting a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while installing the sink flange to the sink. To stay clear of scraping your sink or the flange, position a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these pieces in position.

7. Remove the dishwashing machine ko plug.
If using a dishwasher, you will certainly need to tap out the dishwashing machine ko plug. Lay the garbage disposal on its side as well as utilize a screwdriver and also hammer to tap it out. Next, get rid of the loose knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Transform the garbage disposal over as well as remove electrical cover plate. Take out cords. Place cable adapter (not included) and also run electrical cord via access opening on base of garbage disposal. Tighten up cable television port. Push cables right into garbage disposal (do not displace cardboard guard) and replace electric cover plate.
If you have a hardwired unit as well as you’re wanting to affix a cable, you will certainly need a power cord set.
Corded Device:
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the reduced installing ring up until all 3 tabs are locked into the placing assembly. The garbage disposal will certainly now hang by itself.
10. Insert the discharge tube.
Place the discharge tube into the discharge coupler, then glide the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain trap.
Turn the garbage disposal to make sure that the discharge tube is lined up with the drain catch. If the discharge tube is too long, cut off as much as needed. If it is as well short, you can buy an extension.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwashing machine, it might be connected through an air space. Utilize a hose clamp to connect the drain pipe to the dishwashing machine inlet. Since whatever is installed as well as ready, secure the garbage disposal to the sink mounting setting up using the wrenchette that included the system. For Development models, put the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink till it snaps into area.

13. Check the garbage disposal.
For all designs, you must examine for leaks at the sink flange, dishwasher, tail-pipe as well as installing assembly connections. Lastly, switch on the electric breaker to evaluate its procedure.
How to Choose a Garbage Disposal in Hidden Hills
How to Install a Garbage Disposal in Hidden Hills