1. Turn off power to the garbage disposal and also detach the down trap.
Shut off the electric power at the fuse box or circuit breaker. After that, using adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the placing assembly.
Support the garbage disposal with one hand and place completion of the wrenchette or screwdriver into the best side of one installing lug on the lower mounting ring. Lift the garbage disposal slightly as well as loosen the reduced installing ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is free from the placing assembly.
3. Separate the electrical.
Lay the garbage disposal on its side and remove the electric cover plate from all-time low. Loosen the eco-friendly ground screw and eliminate cord adapters. Detach garbage disposal cords from electrical supply cords. Loosen screws on the electric clamp connector and also eliminate cords from the garbage disposal.

4. Eliminate existing installing hardware if hardware substitute needed. Or else skip to tip 12.
To eliminate the existing mounting equipment, loosen the three placing screws, tear the breeze ring off with a screwdriver and also remove the old installing assembly.

5. Remove the old sink flange and putty.
Press the old sink flange up via the sink opening. Utilize a screwdriver or putty knife to very carefully scratch all old putty from the side of the sink hole
. Install the brand-new sink flange, gasket as well as rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drainpipe opening as well as press it into location. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in position while installing the sink flange to the sink. To avoid scraping your sink or the flange, put a towel between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and placing flange over the sink flange. Hold these pieces in place.

7. Eliminate the dish washer knockout plug.
If utilizing a dish washer, you will require to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and make use of a screwdriver as well as hammer to touch it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Turn the garbage disposal over and also eliminate electric cover plate. Take out cables. Insert cable television port (not included) and also run electrical cable via gain access to opening on bottom of garbage disposal. Tighten cable adapter. Press wires into garbage disposal (do not displace cardboard guard) and replace electric cover plate.
If you have a hardwired unit as well as you’re looking to affix a cord, you will certainly require a power cord package.
Corded Device:
For a garbage disposal with a factory-installed cable, simply connect in to the outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the reduced mounting ring till all 3 tabs are locked right into the installing assembly. The garbage disposal will certainly now hang on its own.
10. Insert the discharge tube.
Put the discharge tube right into the discharge coupler, then glide the clamp over the discharge tube as well as placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain trap.
Turn the garbage disposal to make sure that the discharge tube is lined up with the drainpipe catch. If the discharge tube is too long, removed as long as needed. If it is as well short, you can buy an extension.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it may be attached via an air void. Utilize a pipe clamp to affix the drain hose to the dishwasher inlet. Since every little thing is installed as well as in position, secure the garbage disposal to the sink mounting setting up making use of the wrenchette that featured the unit. For Advancement versions, put the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink till it snaps right into area.

13. Evaluate the garbage disposal.
For all versions, you ought to evaluate for leakages at the sink flange, dishwasher, tail-pipe and mounting assembly links. Finally, activate the electric breaker to evaluate its procedure.
Garbage Disposal Installation in Lake Balboa
Installing a New Garbage Disposal in Lake Balboa