05 Feb. 21
Installing a Replacement Garbage Disposal in North Hollywood
1. Turn off power to the garbage disposal as well as disconnect the down catch.
Shut off the electrical power at the circuit box or circuit breaker. After that, making use of flexible pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Support the garbage disposal with one hand and also place the end of the wrenchette or screwdriver right into the ideal side of one mounting lug on the lower installing ring. Lift the garbage disposal somewhat and also loosen up the lower mounting ring by pressing or pulling the wrenchette or screwdriver to the left up until the garbage disposal is free from the installing setting up.
3. Detach the electric.
Lay the garbage disposal on its side as well as eliminate the electric cover plate from the bottom. Loosen the eco-friendly ground screw as well as remove cord connectors. Detach garbage disposal cords from electrical supply cables. Loosen up screws on the electric clamp adapter and get rid of wires from the garbage disposal.
4. Get rid of existing mounting hardware if equipment replacement required. Otherwise miss to step 12.
To eliminate the existing installing equipment, loosen up the 3 mounting screws, tear the breeze ring off with a screwdriver and get rid of the old installing setting up.
5. Get rid of the old sink flange as well as putty.
Press the old sink flange up through the sink hole. Make use of a screwdriver or putty knife to meticulously scrape all old putty from the edge of the sink hole
. Set up the brand-new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Go down the new sink flange right into the drain opening and also press it right into area. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly aid hold the sink flange in place while mounting the sink flange to the sink. To stay clear of damaging your sink or the flange, place a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these items in place.
7. Eliminate the dish washer knockout plug.
If making use of a dishwashing machine, you will certainly need to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and use a screwdriver and hammer to tap it out. Next, get rid of the loosened knockout plug from inside the garbage disposal.
8. Link the electric.
Transform the garbage disposal over as well as remove electric cover plate. Pull out cables. Put cable television adapter (not included) and run electrical cable television with gain access to opening on bottom of garbage disposal. Tighten cable connector. Push cords into garbage disposal (do not displace cardboard guard) and also replace electric cover plate.
If you have a hardwired system and also you’re aiming to affix a cord, you will need a power cord set.
For a garbage disposal with a factory-installed cord, just connect in to the outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the lower installing ring till all 3 tabs are secured right into the placing assembly. The garbage disposal will currently hang by itself.
10. Place the discharge tube.
Place the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain catch.
Rotate the garbage disposal to ensure that the discharge tube is lined up with the drainpipe trap. If the discharge tube is too long, cut off as much as needed. If it is also brief, you can acquire an extension.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dish washer, it may be attached via an air space. Utilize a hose clamp to connect the drainpipe hose pipe to the dishwashing machine inlet. Since every little thing is installed and also ready, secure the garbage disposal to the sink placing assembly using the wrenchette that featured the system. For Development versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink till it snaps into location.
13. Evaluate the garbage disposal.
For all designs, you ought to test for leaks at the sink flange, dish washer, tail-pipe and installing assembly connections. Ultimately, switch on the electric breaker to check its procedure.
Garbage Disposal Installation in North Hollywood
How to Choose a Garbage Disposal in North Hollywood