1. Switch off power to the garbage disposal and also disconnect the down catch.
Shut off the electrical power at the fuse box or breaker. After that, making use of flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the placing setting up.
Assistance the garbage disposal with one hand as well as insert the end of the wrenchette or screwdriver right into the right side of one placing lug on the reduced placing ring. Lift the garbage disposal a little as well as loosen the lower mounting ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is free from the placing setting up.
3. Detach the electric.
Lay the garbage disposal on its side and also remove the electrical cover plate from all-time low. Loosen up the green ground screw and eliminate wire ports. Disconnect garbage disposal wires from electrical supply cords. Loosen screws on the electrical clamp adapter as well as eliminate cords from the garbage disposal.

4. Remove existing mounting hardware if equipment replacement required. Or else skip to tip 12.
To get rid of the existing placing hardware, loosen up the 3 placing screws, tear the breeze ring off with a screwdriver as well as get rid of the old installing assembly.

5. Get rid of the old sink flange and putty.
Push the old sink flange up through the sink hole. Use a screwdriver or putty knife to carefully scrape all old putty from the edge of the sink hole
. Mount the new sink flange, gasket and also rings.
Area a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Drop the new sink flange right into the drain opening as well as press it into area. Placing a weight, such as the garbage disposal, in addition to the sink flange will certainly aid hold the sink flange in position while installing the sink flange to the sink. To prevent scraping your sink or the flange, place a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange and mounting flange over the sink flange. Hold these items in position.

7. Eliminate the dishwasher knockout plug.
If using a dish washer, you will require to tap out the dishwashing machine ko plug. Lay the garbage disposal on its side and make use of a screwdriver and also hammer to tap it out. Next off, eliminate the loose ko plug from inside the garbage disposal.
8. Attach the electric.
Hardwired Unit:
Transform the garbage disposal over as well as remove electrical cover plate. Take out wires. Insert cable adapter (not included) and run electrical cable via gain access to opening on base of garbage disposal. Tighten wire connector. Press cables right into garbage disposal (do not displace cardboard guard) and also replace electric cover plate.
If you have a hardwired device and you’re looking to connect a cord, you will need a power cable package.
Corded System:
For a garbage disposal with a factory-installed cord, merely plug in to the outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the reduced mounting ring until all three tabs are secured right into the mounting setting up. The garbage disposal will certainly now hang by itself.
10. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then glide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Turn the garbage disposal so that the discharge tube is straightened with the drain trap. If the discharge tube is also long, removed as much as required. If it is also brief, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwashing machine, it may be linked with an air space. Make use of a hose clamp to attach the drain hose to the dish washer inlet. Since whatever is mounted as well as in position, lock the garbage disposal to the sink mounting assembly making use of the wrenchette that featured the system. For Advancement models, insert the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink up until it snaps right into location.

13. Check the garbage disposal.
For all versions, you should test for leaks at the sink flange, dishwasher, tail-pipe as well as mounting setting up connections. Lastly, turn on the electrical breaker to evaluate its operation.
Garbage Disposal Installation in Sherman Oaks
How to Install a Garbage Disposal in Sherman Oaks