05 Feb. 21

Installing a Substitute Garbage Disposal in West Hills

1. Turn off power to the garbage disposal and also detach the down catch.
Switch off the electric power at the circuit box or circuit breaker. Then, using adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand as well as insert completion of the wrenchette or screwdriver into the right side of one mounting lug on the lower placing ring. Lift the garbage disposal somewhat as well as loosen up the reduced mounting ring by pressing or pulling the wrenchette or screwdriver to the left till the garbage disposal is devoid of the mounting assembly.
3. Detach the electric.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen the eco-friendly ground screw as well as get rid of cable adapters. Detach garbage disposal cables from electric supply wires. Loosen screws on the electric clamp connector and remove cords from the garbage disposal.

4. Eliminate existing installing hardware if equipment replacement needed. Otherwise miss to tip 12.
To remove the existing installing equipment, loosen the three installing screws, tear the snap ring off with a screwdriver and get rid of the old installing assembly.

5. Get rid of the old sink flange and putty.
Push the old sink flange up via the sink opening. Make use of a screwdriver or putty blade to thoroughly scratch all old putty from the side of the sink hole
. Install the new sink flange, gasket and rings.
Place a 1/2 inch rope of plumbing professional’s putty around the drain opening in the sink. Go down the brand-new sink flange right into the drain opening and press it right into location. Positioning a weight, such as the garbage disposal, on top of the sink flange will certainly help hold the sink flange in position while installing the sink flange to the sink. To avoid damaging your sink or the flange, place a towel between the sink surface area as well as the weight. From under the sink, slide the fiber gasket, back-up flange and also mounting flange over the sink flange. Hold these pieces in position.

7. Eliminate the dish washer ko plug.
If utilizing a dishwashing machine, you will certainly need to touch out the dishwasher knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver and also hammer to touch it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
8. Attach the electric.
Hardwired Device:
Transform the garbage disposal over and also get rid of electrical cover plate. Pull out cables. Insert cable television port (not consisted of) and also run electrical cable via accessibility opening on bottom of garbage disposal. Tighten cable television adapter. Press wires right into garbage disposal (do not displace cardboard shield) as well as change electric cover plate.
If you have a hardwired unit and also you’re wanting to affix a cable, you will require a power cord package.
Corded Unit:
For a garbage disposal with a factory-installed cable, simply connect in to the outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the reduced installing ring up until all 3 tabs are locked right into the installing assembly. The garbage disposal will certainly now hang on its own.
10. Insert the discharge tube.
Put the discharge tube right into the discharge coupler, then slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Revolve the garbage disposal so that the discharge tube is straightened with the drain catch. If the discharge tube is also long, cut off as much as required. If it is also short, you can buy an extension.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dishwasher, it might be connected via an air gap. Use a tube clamp to affix the drainpipe hose pipe to the dishwashing machine inlet. Since everything is set up as well as in position, lock the garbage disposal to the sink installing assembly using the wrenchette that came with the system. For Evolution versions, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink till it snaps into area.

13. Check the garbage disposal.
For all models, you should check for leakages at the sink flange, dish washer, tail-pipe and mounting setting up links. Ultimately, turn on the electric breaker to check its procedure.
Garbage Disposal Installation in West Hills
How to Install a Garbage Disposal in West Hills