05 Feb. 21
Mounting a Replacement Garbage Disposal in Studio City
1. Turn off power to the garbage disposal and disconnect the down catch.
Shut off the electric power at the fuse box or breaker. After that, making use of flexible pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Support the garbage disposal with one hand and also put the end of the wrenchette or screwdriver into the best side of one installing lug on the lower installing ring. Lift the garbage disposal somewhat as well as loosen up the reduced mounting ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the placing setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side as well as remove the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw as well as get rid of cord adapters. Disconnect garbage disposal wires from electric supply cords. Loosen screws on the electric clamp adapter and also get rid of cords from the garbage disposal.
4. Eliminate existing installing equipment if equipment substitute required. Or else avoid to step 12.
To get rid of the existing mounting equipment, loosen the three placing screws, tear the snap ring off with a screwdriver as well as get rid of the old mounting setting up.
5. Remove the old sink flange and also putty.
Push the old sink flange up via the sink hole. Make use of a screwdriver or putty blade to carefully scuff all old putty from the side of the sink hole
. Install the brand-new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drain opening as well as press it right into place. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these pieces in place.
7. Remove the dish washer ko plug.
If making use of a dishwasher, you will need to touch out the dishwasher ko plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to tap it out. Next, eliminate the loosened ko plug from inside the garbage disposal.
8. Connect the electric.
Transform the garbage disposal over and get rid of electric cover plate. Pull out cords. Put cable television connector (not included) and run electrical cable via gain access to opening on bottom of garbage disposal. Tighten up cord adapter. Push wires into garbage disposal (do not displace cardboard shield) and also change electrical cover plate.
If you have a hardwired unit as well as you’re looking to connect a cable, you will need a power cord package.
For a garbage disposal with a factory-installed cable, simply plug in to the electrical outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the lower mounting ring up until all 3 tabs are secured right into the placing assembly. The garbage disposal will certainly now hang by itself.
10. Place the discharge tube.
Insert the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drainpipe catch. If the discharge tube is also long, cut off as high as essential. If it is as well short, you can buy an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwasher, it might be linked via an air space. Make use of a tube clamp to affix the drain hose to the dishwasher inlet. Now that whatever is installed as well as in position, lock the garbage disposal to the sink installing assembly using the wrenchette that included the device. For Development versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink until it snaps right into area.
13. Examine the garbage disposal.
For all models, you ought to check for leaks at the sink flange, dish washer, tail-pipe as well as placing assembly links. Lastly, switch on the electric breaker to examine its procedure.
How to Choose a Garbage Disposal in Studio City
Installing a New Garbage Disposal in Studio City