1. Shut off power to the garbage disposal as well as disconnect the down trap.
Switch off the electrical power at the circuit box or circuit breaker. Then, utilizing flexible pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand and insert completion of the wrenchette or screwdriver into the ideal side of one mounting lug on the reduced installing ring. Lift the garbage disposal somewhat and also loosen the reduced mounting ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is devoid of the placing setting up.
3. Separate the electric.
Lay the garbage disposal on its side and eliminate the electrical cover plate from the bottom. Loosen up the eco-friendly ground screw and remove wire ports. Detach garbage disposal cords from electric supply cables. Loosen up screws on the electrical clamp connector and get rid of wires from the garbage disposal.

4. Get rid of existing placing hardware if hardware substitute required. Or else avoid to step 12.
To get rid of the existing installing hardware, loosen up the three installing screws, pry the snap ring off with a screwdriver and get rid of the old placing setting up.

5. Eliminate the old sink flange and also putty.
Press the old sink flange up via the sink hole. Make use of a screwdriver or putty blade to thoroughly scratch all old putty from the side of the sink opening
. Set up the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing professional’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange right into the drain opening as well as press it into area. Placing a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while placing the sink flange to the sink. To prevent damaging your sink or the flange, place a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in position.

7. Remove the dish washer knockout plug.
If using a dishwashing machine, you will require to touch out the dishwasher ko plug. Lay the garbage disposal on its side and also make use of a screwdriver and hammer to tap it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
8. Link the electrical.
Hardwired Device:
Transform the garbage disposal over and also remove electric cover plate. Pull out wires. Put cable port (not consisted of) and also run electrical wire with gain access to opening on base of garbage disposal. Tighten up cable television adapter. Press cords right into garbage disposal (do not displace cardboard shield) and replace electrical cover plate.
If you have a hardwired system and you’re wanting to connect a cable, you will require a power cord set.
Corded System:
For a garbage disposal with a factory-installed cord, simply connect in to the electrical outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the lower installing ring till all three tabs are locked into the mounting assembly. The garbage disposal will certainly now hang on its own.
10. Put the discharge tube.
Place the discharge tube right into the discharge coupler, then slide the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Rotate the garbage disposal to make sure that the discharge tube is straightened with the drain trap. If the discharge tube is as well long, cut off as long as necessary. If it is too brief, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwashing machine, it might be connected via an air gap. Utilize a hose clamp to connect the drain hose to the dishwashing machine inlet. Since every little thing is set up and in position, lock the garbage disposal to the sink installing assembly utilizing the wrenchette that came with the system. For Advancement models, insert the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink until it snaps into area.

13. Examine the garbage disposal.
For all models, you need to evaluate for leaks at the sink flange, dishwasher, tail-pipe and also installing setting up links. Finally, activate the electric breaker to evaluate its procedure.
How to Choose a Garbage Disposal in Encino