1. Shut off power to the garbage disposal and also detach the down catch.
Shut off the electric power at the circuit box or breaker. After that, utilizing adjustable pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand and put completion of the wrenchette or screwdriver right into the ideal side of one mounting lug on the lower installing ring. Raise the garbage disposal slightly and loosen up the reduced mounting ring by pushing or drawing the wrenchette or screwdriver to the left until the garbage disposal is devoid of the mounting setting up.
3. Detach the electric.
Lay the garbage disposal on its side and eliminate the electrical cover plate from the bottom. Loosen the green ground screw as well as eliminate cord connectors. Detach garbage disposal cables from electrical supply cables. Loosen up screws on the electrical clamp connector as well as get rid of cords from the garbage disposal.
4. Remove existing mounting hardware if hardware substitute needed. Or else skip to step 12.
To remove the existing mounting equipment, loosen the three installing screws, tear the breeze ring off with a screwdriver and get rid of the old installing setting up.
5. Eliminate the old sink flange and also putty.
Push the old sink flange up through the sink opening. Make use of a screwdriver or putty knife to very carefully scrape all old putty from the edge of the sink hole
. Mount the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it right into area. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in place while installing the sink flange to the sink. To avoid scratching your sink or the flange, position a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these pieces in position.
7. Eliminate the dish washer knockout plug.
If making use of a dishwasher, you will certainly require to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver as well as hammer to tap it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
8. Link the electrical.
Transform the garbage disposal over and also eliminate electric cover plate. Pull out cords. Place cord connector (not included) as well as run electric wire through access opening on base of garbage disposal. Tighten wire connector. Push wires into garbage disposal (do not displace cardboard shield) and also replace electric cover plate.
If you have a hardwired unit as well as you’re seeking to attach a cable, you will certainly require a power cable package.
For a garbage disposal with a factory-installed cable, simply plug in to the electrical outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the reduced installing ring up until all three tabs are locked right into the mounting setting up. The garbage disposal will currently hang by itself.
10. Put the discharge tube.
Put the discharge tube into the discharge coupler, then slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain catch.
Turn the garbage disposal to ensure that the discharge tube is lined up with the drainpipe trap. If the discharge tube is also long, cut off as high as essential. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dish washer, it might be attached via an air gap. Make use of a hose pipe clamp to connect the drain hose pipe to the dishwashing machine inlet. Now that every little thing is installed and in position, lock the garbage disposal to the sink placing setting up making use of the wrenchette that featured the device. For Evolution designs, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink up until it snaps into area.
13. Check the garbage disposal.
For all models, you must check for leaks at the sink flange, dish washer, tail-pipe as well as placing assembly links. Ultimately, switch on the electric breaker to examine its operation.
Installing a New Garbage Disposal in Valley Village
Whatever You Need to Learn About Trash Disposals in Valley Village