1. Switch off power to the garbage disposal and detach the down trap.
Shut off the electrical power at the fuse box or breaker. After that, utilizing adjustable pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing assembly.
Assistance the garbage disposal with one hand and also place completion of the wrenchette or screwdriver into the ideal side of one placing lug on the reduced installing ring. Lift the garbage disposal somewhat as well as loosen up the lower mounting ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the installing setting up.
3. Separate the electrical.
Lay the garbage disposal on its side and also eliminate the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw as well as remove cord adapters. Disconnect garbage disposal cords from electrical supply cables. Loosen up screws on the electric clamp adapter as well as remove cords from the garbage disposal.
4. Get rid of existing installing equipment if hardware replacement needed. Otherwise skip to step 12.
To remove the existing installing hardware, loosen the 3 installing screws, pry the breeze ring off with a screwdriver and also get rid of the old placing assembly.
5. Get rid of the old sink flange and also putty.
Press the old sink flange up through the sink opening. Use a screwdriver or putty knife to thoroughly scratch all old putty from the edge of the sink opening
. Set up the brand-new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drainpipe opening as well as press it into location. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in position while mounting the sink flange to the sink. To prevent scratching your sink or the flange, place a towel between the sink surface as well as the weight. From under the sink, slide the fiber gasket, back-up flange and mounting flange over the sink flange. Hold these items in place.
7. Get rid of the dish washer ko plug.
If using a dishwashing machine, you will need to tap out the dish washer knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to tap it out. Next off, eliminate the loose knockout plug from inside the garbage disposal.
8. Link the electric.
Transform the garbage disposal over as well as get rid of electric cover plate. Pull out cables. Put cable television connector (not consisted of) and run electric cable television via accessibility opening on bottom of garbage disposal. Tighten up cord adapter. Press cables right into garbage disposal (do not displace cardboard guard) and replace electrical cover plate.
If you have a hardwired unit and also you’re looking to attach a cord, you will require a power cord set.
For a garbage disposal with a factory-installed cord, merely plug in to the electrical outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the lower mounting ring till all 3 tabs are locked into the placing setting up. The garbage disposal will currently hang on its own.
10. Place the discharge tube.
Put the discharge tube right into the discharge coupler, then glide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain catch.
Turn the garbage disposal to ensure that the discharge tube is lined up with the drain catch. If the discharge tube is too long, removed as much as essential. If it is too brief, you can purchase an expansion.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dish washer, it might be linked via an air void. Utilize a pipe clamp to connect the drain tube to the dishwasher inlet. Since every little thing is installed and also ready, lock the garbage disposal to the sink placing setting up making use of the wrenchette that featured the system. For Advancement designs, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink until it snaps into location.
13. Check the garbage disposal.
For all models, you ought to test for leakages at the sink flange, dishwasher, tail-pipe as well as placing assembly links. Lastly, switch on the electric breaker to test its operation.
How to Install a Garbage Disposal in Sun Valley
How to Choose a Garbage Disposal in Sun Valley