1. Shut off power to the garbage disposal and also detach the down trap.
Shut off the electrical power at the fuse box or breaker. After that, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand and also place the end of the wrenchette or screwdriver into the right side of one placing lug on the reduced placing ring. Lift the garbage disposal a little as well as loosen the lower installing ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is devoid of the installing setting up.
3. Separate the electrical.
Lay the garbage disposal on its side as well as remove the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw and also get rid of wire ports. Detach garbage disposal cords from electric supply cords. Loosen screws on the electrical clamp adapter and also remove cables from the garbage disposal.
4. Get rid of existing mounting hardware if equipment replacement needed. Otherwise miss to tip 12.
To eliminate the existing placing equipment, loosen the 3 placing screws, tear the breeze ring off with a screwdriver as well as eliminate the old placing assembly.
5. Remove the old sink flange and also putty.
Press the old sink flange up through the sink hole. Utilize a screwdriver or putty blade to meticulously scratch all old putty from the edge of the sink hole
. Mount the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Go down the brand-new sink flange into the drain opening and press it right into area. Placing a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in position while installing the sink flange to the sink. To prevent damaging your sink or the flange, put a towel in between the sink surface area and also the weight. From under the sink, slide the fiber gasket, back-up flange and also placing flange over the sink flange. Hold these pieces in position.
7. Remove the dishwasher knockout plug.
If utilizing a dishwashing machine, you will certainly need to tap out the dish washer ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver and also hammer to tap it out. Next off, remove the loosened knockout plug from inside the garbage disposal.
8. Connect the electrical.
Transform the garbage disposal over as well as eliminate electrical cover plate. Take out cables. Put cord port (not included) and also run electric cord with gain access to hole on base of garbage disposal. Tighten cable adapter. Press wires into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired device as well as you’re seeking to affix a cable, you will require a power cable kit.
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, transform the lower placing ring up until all 3 tabs are secured right into the installing setting up. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Put the discharge tube into the discharge coupler, then move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Turn the garbage disposal so that the discharge tube is aligned with the drainpipe trap. If the discharge tube is too long, removed as high as essential. If it is as well short, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwasher, it may be connected through an air void. Utilize a hose clamp to affix the drain pipe to the dishwashing machine inlet. Since everything is installed and also ready, secure the garbage disposal to the sink mounting assembly using the wrenchette that came with the device. For Advancement models, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink up until it snaps right into area.
13. Examine the garbage disposal.
For all designs, you should evaluate for leaks at the sink flange, dishwasher, tail-pipe as well as placing setting up connections. Finally, activate the electrical breaker to test its procedure.
Installing a New Garbage Disposal in Valley Glen
Whatever You Required to Understand About Garbage Disposals in Valley Glen