1. Shut off power to the garbage disposal and also detach the down catch.
Turn off the electrical power at the fuse box or breaker. After that, making use of flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand as well as place the end of the wrenchette or screwdriver into the best side of one installing lug on the lower installing ring. Lift the garbage disposal slightly as well as loosen up the lower placing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is without the mounting setting up.
3. Disconnect the electric.
Lay the garbage disposal on its side and also remove the electric cover plate from all-time low. Loosen up the environment-friendly ground screw and eliminate cord ports. Disconnect garbage disposal cables from electrical supply cords. Loosen screws on the electric clamp adapter as well as get rid of cables from the garbage disposal.

4. Get rid of existing mounting hardware if hardware substitute needed. Otherwise avoid to tip 12.
To get rid of the existing placing hardware, loosen up the three mounting screws, tear the breeze ring off with a screwdriver and remove the old placing setting up.

5. Get rid of the old sink flange as well as putty.
Push the old sink flange up through the sink opening. Make use of a screwdriver or putty blade to meticulously scuff all old putty from the edge of the sink hole
. Set up the new sink flange, gasket and also rings.
Area a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange right into the drainpipe opening as well as press it into place. Positioning a weight, such as the garbage disposal, on top of the sink flange will certainly aid hold the sink flange in place while mounting the sink flange to the sink. To stay clear of scratching your sink or the flange, position a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and also installing flange over the sink flange. Hold these pieces in place.

7. Eliminate the dish washer ko plug.
If utilizing a dishwashing machine, you will require to touch out the dishwasher knockout plug. Lay the garbage disposal on its side and use a screwdriver and also hammer to touch it out. Next, eliminate the loose knockout plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired System:
Turn the garbage disposal over as well as eliminate electrical cover plate. Pull out cables. Put cable television port (not consisted of) and run electric wire with access hole on base of garbage disposal. Tighten cord connector. Press cables into garbage disposal (do not displace cardboard shield) and replace electric cover plate.
If you have a hardwired system as well as you’re seeking to attach a cord, you will certainly need a power cable kit.
Corded System:
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three placing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the reduced placing ring up until all three tabs are locked into the installing setting up. The garbage disposal will now hang by itself.
10. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then slide the clamp over the discharge tube as well as placement it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain catch.
Rotate the garbage disposal so that the discharge tube is lined up with the drainpipe catch. If the discharge tube is as well long, removed as much as needed. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dish washer, it might be attached via an air space. Make use of a tube clamp to connect the drain hose to the dishwashing machine inlet. Now that every little thing is mounted and also ready, lock the garbage disposal to the sink mounting assembly making use of the wrenchette that featured the unit. For Evolution versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pressing it into the sink till it breaks into location.

13. Test the garbage disposal.
For all designs, you must evaluate for leakages at the sink flange, dishwasher, tail-pipe and also installing setting up links. Ultimately, switch on the electrical breaker to check its operation.
How to Install a Garbage Disposal in Van Nuys
Whatever You Need to Learn About Waste Disposals in Van Nuys