1. Disconnect the p-trap and the horizontal extension pipe.
Big channel-lock pliers or a monkey wrench work well to loosen up the nuts holding the pipes together. When both links are totally free, get rid of the components. You might want to clean up the horizontal drainpipe pipe to remove any type of feasible blockage. (This is not required in brand-new building.).
2. Disconnect the down drain.
Making use of large channel-lock pliers, disconnect the down drainpipe originating from the sink and the link that affixes it to the p-trap. When both links are complimentary, remove the components.
3. Loosen the large nut.
Unscrew the large nut that holds the filter in position beneath the sink. Remove the strainer body.
4. Pry off the snap ring as well as wipe the old plumbing’s putty.
Using a flathead screwdriver, loosen up the 3 screws on the placing assembly as well as tear off the snap ring. Wipe the old plumbing’s putty that borders the side of the drainpipe opening.
5. Mount the new sink flange.
Area a 1/2″ rope of plumbing technician’s putty around the drain opening in the sink. Drop the brand-new sink flange right into the drain opening and also press it into place. Putting a weight, such as your garbage disposal, in addition to the sink flange will assist hold the sink flange in position while placing it to the sink. To prevent scraping your sink or the flange, position a towel between the sink surface area as well as the weight.
6. Mount gasket and also flanges.
From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these items in position.
7. Slip on the installing and also snap rings.
Next off, slip on the mounting ring and break ring. Tighten the 3 placing screws, alternately tightening each screw a couple of turns at once up until the installing assembly is evenly and also firmly seated against the bottom of the sink.
8. Get rid of the dishwasher knockout plug.
If utilizing a dish washer, you will certainly need to tap out the dish washer knockout plug. Lay the garbage disposal on its side as well as use a screwdriver as well as hammer to tap it out. Next off, eliminate the loose knockout plug from inside the garbage disposal.
9. Link the electric.
Hardwired Unit:.
Turn the garbage disposal over and remove electric cover plate. Take out cables. Insert cable connector (not included) and run electric wire with gain access to hole on base of garbage disposal. Tighten up cord connector. Press cables into garbage disposal (do not displace cardboard shield) and replace electric cover plate.
If you have a hardwired unit as well as you’re looking to attach a cable, you will need a power cable package.
Corded System:.
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after finishing the remainder of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, transform the lower placing ring till all three tabs are locked into the installing assembly.
11. Put the discharge tube.
Put the discharge tube right into the discharge coupler, after that glide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drainpipe pipeline.
Revolve the garbage disposal so that the discharge tube is aligned with the drain trap. If the discharge tube is also long, cut off as a lot of the tube as needed. If it is also short, you can purchase an extension. If you are connecting the garbage disposal to a dish washer, it may be linked with an air void. Utilize a hose clamp to attach the drainpipe hose to the dish washer inlet.
13. Lock the garbage disposal in position.
Since everything is installed as well as in position, lock the garbage disposal to the sink mounting setting up making use of the wrench that included the unit. Insert the Quiet Collar Sink Baffle into the sink opening by pushing it right into the sink up until it breaks right into location.
14. Test the garbage disposal.
Examination for leaks at the sink flange, dish washer, tail-pipe and also installing assembly connections. Lastly, turn on the electric breaker to check its procedure. Enjoy your brand-new garbage disposal!
Garbage Disposal Installation in Sunland-Tujunga
How to Install a Garbage Disposal in Sunland-Tujunga