1. Shut off power to the garbage disposal and also disconnect the down trap.
Switch off the electric power at the fuse box or circuit breaker. After that, using flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand and also put the end of the wrenchette or screwdriver into the best side of one installing lug on the reduced mounting ring. Raise the garbage disposal a little as well as loosen up the lower placing ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is without the installing assembly.
3. Detach the electric.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen the environment-friendly ground screw and eliminate cord adapters. Disconnect garbage disposal cords from electrical supply cords. Loosen screws on the electrical clamp adapter and get rid of wires from the garbage disposal.
4. Eliminate existing mounting equipment if equipment substitute required. Otherwise skip to step 12.
To eliminate the existing placing hardware, loosen the three mounting screws, pry the snap ring off with a screwdriver and also get rid of the old mounting assembly.
5. Eliminate the old sink flange and putty.
Press the old sink flange up through the sink opening. Use a screwdriver or putty blade to thoroughly scuff all old putty from the edge of the sink hole
. Mount the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumbing professional’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drain opening as well as press it right into area. Placing a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in position while placing the sink flange to the sink. To stay clear of scraping your sink or the flange, put a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange and also installing flange over the sink flange. Hold these items in position.
7. Get rid of the dishwashing machine ko plug.
If utilizing a dishwasher, you will certainly need to tap out the dish washer ko plug. Lay the garbage disposal on its side and also make use of a screwdriver as well as hammer to touch it out. Next off, get rid of the loose ko plug from inside the garbage disposal.
8. Connect the electrical.
Turn the garbage disposal over and get rid of electrical cover plate. Pull out cables. Put cord connector (not included) and run electrical cable television via accessibility hole on base of garbage disposal. Tighten cable television connector. Press wires right into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired device and you’re looking to affix a cord, you will certainly require a power cord kit.
For a garbage disposal with a factory-installed cable, simply connect in to the electrical outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, transform the reduced placing ring up until all three tabs are secured right into the placing setting up. The garbage disposal will certainly now hang by itself.
10. Place the discharge tube.
Put the discharge tube right into the discharge coupler, after that slide the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Revolve the garbage disposal to make sure that the discharge tube is straightened with the drain trap. If the discharge tube is also long, cut off as long as essential. If it is as well brief, you can buy an extension.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dish washer, it may be attached via an air space. Use a hose pipe clamp to attach the drainpipe tube to the dish washer inlet. Since everything is set up and ready, secure the garbage disposal to the sink mounting setting up using the wrenchette that included the system. For Development models, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink until it breaks into place.
13. Evaluate the garbage disposal.
For all versions, you need to check for leaks at the sink flange, dishwasher, tail-pipe and installing setting up links. Lastly, turn on the electrical breaker to evaluate its procedure.
How to Choose a Garbage Disposal in San Fernando
Everything You Need to Understand About Garbage Disposals in San Fernando