05 Feb. 21

Can i repair my leaky faucet by myself? in Van Nuys

Tossing your faucet merely because it is leaking is wasteful and
costly. Tons of brass, steel, silicone, chrome-plated plastic, and die-cast zinc
every year end up in garbage dumps due to
the fact that faucets are old and have reached completion of their life
expectancies. But numerous other tons are
needlessly disposed of due to leaks that homeowners did not think could be repaired.
Hanging onto a leaky faucet is pricey, too. The United States
Environmental Protection Agency approximates that the average U.S.
household wastes 9,400 gallons of water yearly from
home leaks. This suffices to run 300 loads of laundry. Leaks alone represent almost one trillion gallons of wasted water across the U.S. per

Water is a significantly dwindling resource.
Given that the monthly cost of water for
a typical U.S. household increased by 52% from 2010 to 2017, this is a
pushing issue that surpasses just a matter of an
annoying drip during the night.
Become part of the solution by repairing your own dripping faucet, both
for your own sake and for the good of the earth. This short article will assist you
fix any of the 4 most basic kinds of
home faucets. It might be much easier than you
assume, and it generally will be cheaper than acquiring a new faucet.
Prior to You Begin Your Repair
Faucet repair uses fairly couple of tools, a number
of which you might already have on hand. Before you start
your repair, you will want to have all tools and products nearby.
Tools and Products
Allen Wrenches (Hex Wrenches).
Channellock-Style Pliers.
Clean Towel.
Clean Plastic Bin.
Egg Carton, Optional (preferably Styrofoam).

Duct Tape.
Distilled Vinegar.
Different Cleaning Implements: Q-Tip, Scouring Pad, Cloth
Rags, Old Toothbrush.
Plumbing professional's Grease.
Utility Knife.
Components Specific to Your Kind Of Faucet.
Preparation and Shut-Down Procedures.
Shut Water Off: Turn off water at the faucet.
Location Container: Put container below sink, near the water system lines. This will collect drips after you detach the
supply lines.
Disconnect Water: Shut off the two water system lines
under the sink (cold and hot). Disconnect water system valve
to sink under the cabinet. Let water drain into container.
Close Drain: Close with stopper. Ensure that no parts drop the sink by
sealing the sink drain with a couple of strips of duct tape.
Safeguard Fixtures: Use duct tape to plier jaws to avoid
scratching components. One terrific recommendation is
to cut off the fingers from an old pair of gloves and slip the fingers onto the plier jaws. For the
supreme in protection, purchase soft-jaw pliers at your local hardware

Prepare Collection Area: Set out bin, towel, and optional egg container beside
sink to aid in parts removal. Styrofoam egg containers work best,
given that they are not affected by water.
Prepare Cleansing Items: Place distilled vinegar and cleaning
implements near bin to remove mineral deposits on parts.
How to Fix Leaky Compression Faucets.
The simplest and oldest type of faucet, the compression faucet is
differentiated by its separate hot and cold controls which
need you to turn them clockwise to shut off the water.
Time Allotted: 30 minutes.
Tools and Products: Channellock-type pliers; flat-head and Phillips screwdrivers; replacement
washer; plumbing technician's grease; O-ring (optional).
Eliminate the faucet handles with pliers and flat-head screwdriver.
Remove the screw that attaches the handles to the valve stem with your
Phillips head screwdriver.
Pull the handle up to remove it.
Get rid of valve stem assembly cover, then get rid of the assembly
With your soft pliers or wrench, get rid of the hex-nut section of the valve stem
assembly by turning nut counter-clockwise.
Unscrew the hex nut the rest of the way and remove.
Locate the stem washer, which will be found at the bottom of the valve assembly. It
may be worn down and in need of replacement.
Remove brass screw protecting the stem washer in place.

Clean the washer holder area with vinegar and toothbrush to eliminate mineral deposits.
Eliminate old washer and utilize this as your model for when you go to the
shop for a replacement. If the O-ring appeared to be used, you can change this as
Reassemble: push the new washer into valve seat, then connect with the
brass screw and the new or existing O-ring.
Coat with plumber's grease.
Reassemble rest of faucet assembly.
How to Fix Ceramic Disk Faucets.
Double-control ceramic disk faucets have separate cold and hot controls. The
gadget that starts and stops water circulation is a cartridge
including a pair of extremely polished ceramic
disks. In some cases, only one side of this assembly might be
leaking. Test this out by at the same time shutting off the
supply of water below the sink to see which side is
Time Allotted: 45 minutes.
Tools and Materials: Pliers; flat-head screwdriver; replacement cartridges; plumber's grease; O-
ring (optional).
Open the plastic or metal cover plate that covers the handles.
The faucet body is secured to the cartridge typically by a Phillips
head screw, though in some cases by an Allen screw. Eliminate the
fastener and separate the faucet body from the cartridge stem.

Get rid of the locking nut with Channellock-type pliers. In some models, you
might likewise find a brass screw on top of the cartridge. If so, remove it and keep it, as you may need it when you install the new cartridge.
Slide out the retaining clip (or locking ring) with pliers, then lift out the cartridge. Take the old
cartridge to a hardware store for an exact replacement.
Soak staying parts in vinegar, then brush off to get rid of deposits.
Reassemble the faucet in reverse. If you saved the brass screw from earlier and it is needed,
install this now.
Switch on your water supply. Check the system
for leaks.
How to Repair Single Cartridge (Sleeve) Faucets.
Cartridge faucets, often found in cooking areas,
generally have a single lever that meets a large,
round base. The lever brings up to start the water circulation. Side to
side motion controls the cold and hot functions. The optional one-
for-one replacement of the self-contained cartridge indicates less fussing with
little parts.

Time Allotted: 45 minutes.
Tools and Products: Allen wrenches; screwdrivers; Channellock-style pliers;
cleaning materials; replacement cartridge (optional, if existing cartridge can
not be cleaned up).
With your Allen wrenches, unscrew and loosen up the set screw, then get rid
of the handle.

Raise the ornamental cap straight off. These are normally
delicate, so beware. Use your hands, not pliers.
With pliers, thoroughly pry the cartridge loose and eliminate further by
hand. The cartridge will have seals on the bottom that you can pry out with the flat-head screwdriver.
With your cleansing implements, clean the seals and the area where the seals rest. To
do this, soak in vinegar and brush off deposits with a Q-tip or old tooth brush. If the
deposits do not free easily, purchase a new cartridge.
With your screwdriver, remove the O-ring from the faucet, coat with
plumbing's grease by hand, then re-install in the faucet body.
Change the cleaned old cartridge or brand-new cartridge, tightening with
the Channellock pliers.
Carefully change the ornamental cap.
Re-install handle, tightening the set screw with the Allen wrenches.910.
What if I don`t quickly attend to a leaky faucet? in Van Nuys
How to Protect Your Home From Leaky Faucets in Van Nuys