1. Separate the p-trap as well as the horizontal expansion pipe.
Huge channel-lock pliers or a pipe wrench work well to loosen up the nuts holding the pipelines with each other. When both connections are cost-free, get rid of the components. You might want to clean the straight drainpipe pipe to remove any type of possible obstruction. (This is not needed in new building and construction.).
2. Detach the down drainpipe.
Utilizing huge channel-lock pliers, detach the down drainpipe coming from the sink as well as the link that connects it to the p-trap. When both connections are totally free, get rid of the components.
3. Loosen the huge nut.
Loosen the large nut that holds the strainer in place beneath the sink. Get rid of the filter body.
4. Tear off the snap ring as well as wipe the old plumber’s putty.
Using a flathead screwdriver, loosen the 3 screws on the placing assembly and also tear off the snap ring. Wipe the old plumbing professional’s putty that surrounds the side of the drain opening.
5. Install the new sink flange.
Area a 1/2″ rope of plumbing technician’s putty around the drain opening in the sink. Go down the brand-new sink flange into the drainpipe opening and press it right into place. Putting a weight, such as your garbage disposal, in addition to the sink flange will aid hold the sink flange in position while placing it to the sink. To avoid scratching your sink or the flange, position a towel between the sink surface area and the weight.
6. Mount gasket and flanges.
From under the sink, slide the fiber gasket, back-up flange as well as installing flange over the sink flange. Hold these items in place.
7. Slip on the installing as well as snap rings.
Next, slip on the installing ring and break ring. Tighten up the three mounting screws, at the same time tightening up each screw a couple of turns at a time until the mounting assembly is evenly and also snugly seated versus the bottom of the sink.
8. Remove the dishwashing machine knockout plug.
If using a dishwasher, you will need to touch out the dish washer ko plug. Lay the garbage disposal on its side and also make use of a screwdriver as well as hammer to tap it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
9. Link the electrical.
Hardwired Device:.
Transform the garbage disposal over and also remove electric cover plate. Pull out cables. Place wire port (not included) and also run electric cable via accessibility opening on base of garbage disposal. Tighten cable port. Push cables right into garbage disposal (do not displace cardboard shield) and replace electric cover plate.
If you have a hardwired system as well as you’re seeking to attach a cord, you will require a power cable kit.
Corded Unit:.
For a garbage disposal with a factory-installed cord, just plug in to the electrical outlet under your sink after completing the rest of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, turn the lower installing ring until all 3 tabs are secured right into the placing assembly.
11. Place the discharge tube.
Place the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drainpipe pipeline.
Revolve the garbage disposal to ensure that the discharge tube is straightened with the drain catch. If the discharge tube is too long, removed as much of the tube as essential. If it is as well short, you can acquire an expansion. If you are attaching the garbage disposal to a dishwashing machine, it might be connected via an air space. Utilize a hose pipe clamp to attach the drainpipe pipe to the dish washer inlet.
13. Lock the garbage disposal in position.
Since whatever is installed and ready, secure the garbage disposal to the sink installing setting up utilizing the wrench that included the system. Put the Quiet Collar Sink Baffle into the sink opening by pushing it into the sink until it snaps into area.
14. Test the garbage disposal.
Examination for leaks at the sink flange, dishwashing machine, tail-pipe and also mounting assembly links. Lastly, activate the electrical breaker to evaluate its procedure. Enjoy your brand-new garbage disposal!
Installing a Replacement Garbage Disposal in Lake Balboa
How to Choose a Garbage Disposal in Lake Balboa