1. Disconnect the p-trap and the straight extension pipeline.
Huge channel-lock pliers or a pipe wrench job well to loosen up the nuts holding the pipelines with each other. When both connections are free, eliminate the components. You might intend to cleanse the straight drain pipe to get rid of any type of feasible obstruction. (This is not essential in brand-new building and construction.).
2. Disconnect the down drainpipe.
Utilizing big channel-lock pliers, separate the down drain originating from the sink and the link that affixes it to the p-trap. When both connections are cost-free, eliminate the components.
3. Loosen the big nut.
Unscrew the huge nut that holds the filter in place below the sink. Eliminate the filter body.
4. Pry off the breeze ring and wipe the old plumbing professional’s putty.
Utilizing a flathead screwdriver, loosen the 3 screws on the mounting assembly and also pry off the breeze ring. Wipe the old plumbing technician’s putty that surrounds the edge of the drainpipe opening.
5. Set up the brand-new sink flange.
Location a 1/2″ rope of plumber’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drain opening as well as press it into location. Putting a weight, such as your garbage disposal, on top of the sink flange will certainly assist hold the sink flange in place while mounting it to the sink. To avoid damaging your sink or the flange, position a towel between the sink surface area as well as the weight.
6. Set up gasket and flanges.
From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in position.
7. Slip on the mounting and snap rings.
Next off, slip on the placing ring as well as break ring. Tighten the 3 installing screws, alternately tightening each screw a few turns each time up until the mounting assembly is equally as well as firmly seated against the bottom of the sink.
8. Eliminate the dish washer knockout plug.
If utilizing a dishwashing machine, you will certainly require to tap out the dish washer ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver as well as hammer to touch it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
9. Link the electric.
Hardwired Unit:.
Turn the garbage disposal over and eliminate electric cover plate. Take out cables. Insert cable television connector (not included) and run electrical cord through accessibility opening on bottom of garbage disposal. Tighten wire adapter. Press wires right into garbage disposal (do not displace cardboard shield) as well as change electrical cover plate.
If you have a hardwired device and also you’re seeking to affix a cord, you will require a power cord kit.
Corded System:.
For a garbage disposal with a factory-installed cord, simply connect in to the electrical outlet under your sink after finishing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by lining up the three placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the reduced mounting ring up until all 3 tabs are locked right into the installing setting up.
11. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and setting it in the groove on the rubber tailpipe coupler.
12. Align the discharge tube with the drainpipe pipe.
Rotate the garbage disposal to ensure that the discharge tube is lined up with the drain trap. If the discharge tube is as well long, removed as a lot of television as necessary. If it is also short, you can purchase an expansion. If you are connecting the garbage disposal to a dish washer, it might be connected via an air space. Use a tube clamp to affix the drainpipe tube to the dishwasher inlet.
13. Lock the garbage disposal in position.
Now that everything is installed and ready, lock the garbage disposal to the sink installing assembly using the wrench that came with the system. Insert the Quiet Collar Sink Baffle into the sink opening by pushing it into the sink up until it breaks into location.
14. Check the garbage disposal.
Examination for leakages at the sink flange, dishwashing machine, tail-pipe and also placing setting up links. Finally, activate the electric breaker to examine its operation. Appreciate your brand-new garbage disposal!
How to Install a Garbage Disposal in San Fernando