05 Feb. 21
Installing a Replacement Garbage Disposal in Tarzana
1. Switch off power to the garbage disposal as well as separate the down trap.
Turn off the electric power at the fuse box or breaker. Then, using adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand and insert the end of the wrenchette or screwdriver right into the appropriate side of one placing lug on the lower installing ring. Lift the garbage disposal a little and loosen up the lower mounting ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting assembly.
3. Separate the electrical.
Lay the garbage disposal on its side and eliminate the electric cover plate from all-time low. Loosen the green ground screw as well as get rid of cord adapters. Separate garbage disposal wires from electric supply wires. Loosen up screws on the electrical clamp connector as well as remove cables from the garbage disposal.
4. Remove existing placing hardware if equipment replacement needed. Or else skip to step 12.
To remove the existing placing hardware, loosen the three installing screws, pry the snap ring off with a screwdriver and remove the old placing setting up.
5. Eliminate the old sink flange and also putty.
Push the old sink flange up with the sink opening. Use a screwdriver or putty knife to thoroughly scuff all old putty from the side of the sink hole
. Set up the brand-new sink flange, gasket and rings.
Location a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the new sink flange right into the drain opening and also press it right into place. Positioning a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in place while installing the sink flange to the sink. To avoid scraping your sink or the flange, position a towel between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and also mounting flange over the sink flange. Hold these pieces in place.
7. Eliminate the dishwashing machine ko plug.
If using a dishwasher, you will need to tap out the dishwasher ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver and also hammer to touch it out. Next off, remove the loosened ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Transform the garbage disposal over and also remove electric cover plate. Take out wires. Insert wire adapter (not included) as well as run electric cable television via accessibility opening on bottom of garbage disposal. Tighten cable television port. Push wires right into garbage disposal (do not displace cardboard shield) and also change electrical cover plate.
If you have a hardwired unit and you’re wanting to affix a cable, you will require a power cable kit.
Corded Device:
For a garbage disposal with a factory-installed cable, merely plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, turn the reduced mounting ring until all 3 tabs are locked into the placing setting up. The garbage disposal will currently hang on its own.
10. Put the discharge tube.
Insert the discharge tube into the discharge coupler, after that glide the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain catch.
Turn the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is too long, cut off as high as necessary. If it is also brief, you can purchase an expansion.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwashing machine, it may be attached via an air gap. Make use of a tube clamp to connect the drainpipe pipe to the dishwashing machine inlet. Since everything is set up as well as ready, secure the garbage disposal to the sink placing setting up using the wrenchette that featured the device. For Advancement models, put the Quiet Collar ® Sink Baffle right into the sink opening by pressing it into the sink till it snaps into area.
13. Examine the garbage disposal.
For all versions, you ought to examine for leakages at the sink flange, dish washer, tail-pipe and also installing setting up links. Lastly, activate the electrical breaker to check its procedure.
How to Install a Garbage Disposal in Tarzana
Installing a New Garbage Disposal in Tarzana