1. Switch off power to the garbage disposal and also disconnect the down catch.
Shut off the electric power at the fuse box or breaker. After that, utilizing adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand as well as insert the end of the wrenchette or screwdriver right into the appropriate side of one installing lug on the lower placing ring. Raise the garbage disposal a little as well as loosen up the lower mounting ring by pushing or drawing the wrenchette or screwdriver to the left till the garbage disposal is without the mounting setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side as well as eliminate the electric cover plate from the bottom. Loosen up the eco-friendly ground screw and also get rid of wire connectors. Detach garbage disposal cords from electrical supply cables. Loosen screws on the electrical clamp port and get rid of wires from the garbage disposal.

4. Get rid of existing installing hardware if hardware substitute needed. Or else skip to tip 12.
To eliminate the existing installing equipment, loosen up the three placing screws, tear the snap ring off with a screwdriver and get rid of the old installing setting up.

5. Remove the old sink flange and also putty.
Press the old sink flange up via the sink opening. Use a screwdriver or putty blade to thoroughly scuff all old putty from the edge of the sink opening
. Mount the new sink flange, gasket and rings.
Place a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the new sink flange right into the drain opening and also press it into area. Placing a weight, such as the garbage disposal, on top of the sink flange will aid hold the sink flange in position while mounting the sink flange to the sink. To avoid scraping your sink or the flange, place a towel between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in position.

7. Remove the dish washer knockout plug.
If using a dish washer, you will certainly require to touch out the dish washer ko plug. Lay the garbage disposal on its side and use a screwdriver and hammer to tap it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired System:
Transform the garbage disposal over as well as get rid of electric cover plate. Pull out wires. Place cable port (not consisted of) as well as run electrical cable television with accessibility opening on bottom of garbage disposal. Tighten cable television connector. Push cords right into garbage disposal (do not displace cardboard guard) as well as change electric cover plate.
If you have a hardwired system and also you’re looking to connect a cable, you will need a power cord set.
Corded Unit:
For a garbage disposal with a factory-installed cord, simply connect in to the electrical outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the reduced placing ring up until all 3 tabs are locked into the installing assembly. The garbage disposal will certainly now hang on its own.
10. Put the discharge tube.
Place the discharge tube right into the discharge coupler, then move the clamp over the discharge tube as well as placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Rotate the garbage disposal so that the discharge tube is lined up with the drain trap. If the discharge tube is also long, cut off as long as necessary. If it is too short, you can buy an expansion.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dish washer, it may be attached through an air void. Utilize a hose pipe clamp to affix the drain hose to the dish washer inlet. Now that every little thing is set up and also ready, lock the garbage disposal to the sink installing assembly making use of the wrenchette that featured the device. For Evolution models, put the Quiet Collar ® Sink Baffle right into the sink opening by pressing it into the sink till it breaks into area.

13. Check the garbage disposal.
For all models, you must evaluate for leakages at the sink flange, dish washer, tail-pipe and also mounting setting up connections. Lastly, turn on the electrical breaker to evaluate its operation.
How to Choose a Garbage Disposal in Winnetka
How to Install a Garbage Disposal in Winnetka