05 Feb. 21
Mounting a Replacement Garbage Disposal in Pacoima
1. Switch off power to the garbage disposal as well as disconnect the down catch.
Shut off the electric power at the circuit box or breaker. Then, utilizing adjustable pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and put completion of the wrenchette or screwdriver into the right side of one installing lug on the reduced installing ring. Lift the garbage disposal somewhat as well as loosen the lower placing ring by pushing or drawing the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and eliminate the electrical cover plate from the bottom. Loosen the eco-friendly ground screw as well as eliminate wire ports. Detach garbage disposal cables from electric supply cables. Loosen screws on the electric clamp adapter and also remove wires from the garbage disposal.
4. Get rid of existing mounting equipment if hardware substitute required. Otherwise miss to tip 12.
To get rid of the existing placing equipment, loosen up the three placing screws, pry the breeze ring off with a screwdriver and get rid of the old placing setting up.
5. Eliminate the old sink flange and also putty.
Push the old sink flange up with the sink opening. Make use of a screwdriver or putty knife to thoroughly scratch all old putty from the edge of the sink hole
. Install the new sink flange, gasket and rings.
Location a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange right into the drain opening as well as press it right into area. Placing a weight, such as the garbage disposal, in addition to the sink flange will certainly help hold the sink flange in place while placing the sink flange to the sink. To prevent damaging your sink or the flange, position a towel in between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and mounting flange over the sink flange. Hold these items in place.
7. Remove the dishwashing machine ko plug.
If utilizing a dishwashing machine, you will require to touch out the dishwasher ko plug. Lay the garbage disposal on its side as well as utilize a screwdriver and hammer to touch it out. Next off, get rid of the loose ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Device:
Turn the garbage disposal over and also eliminate electric cover plate. Pull out wires. Place cord port (not included) and run electric cord with accessibility opening on base of garbage disposal. Tighten up cable television connector. Push cords into garbage disposal (do not displace cardboard guard) and also replace electrical cover plate.
If you have a hardwired system as well as you’re looking to attach a cable, you will require a power cable kit.
Corded Unit:
For a garbage disposal with a factory-installed cord, just connect in to the electrical outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, turn the reduced mounting ring till all 3 tabs are secured into the installing assembly. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Put the discharge tube right into the discharge coupler, after that slide the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Rotate the garbage disposal to make sure that the discharge tube is lined up with the drainpipe trap. If the discharge tube is as well long, removed as much as necessary. If it is too brief, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dish washer, it might be linked with an air gap. Use a tube clamp to connect the drain hose to the dishwasher inlet. Since everything is mounted as well as in position, lock the garbage disposal to the sink placing setting up using the wrenchette that included the device. For Evolution versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink till it snaps into location.
13. Evaluate the garbage disposal.
For all designs, you need to examine for leaks at the sink flange, dishwasher, tail-pipe as well as placing assembly connections. Finally, turn on the electric breaker to test its operation.
How to Install a Garbage Disposal in Pacoima