05 Feb. 21
Mounting a Replacement Garbage Disposal in Sylmar
1. Turn off power to the garbage disposal and separate the down catch.
Switch off the electrical power at the circuit box or circuit breaker. After that, making use of adjustable pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand and insert the end of the wrenchette or screwdriver right into the best side of one mounting lug on the reduced placing ring. Raise the garbage disposal slightly and also loosen the lower installing ring by pressing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is free from the mounting setting up.
3. Separate the electrical.
Lay the garbage disposal on its side and eliminate the electrical cover plate from all-time low. Loosen the environment-friendly ground screw as well as remove cord ports. Disconnect garbage disposal wires from electrical supply cords. Loosen screws on the electric clamp connector and also remove cables from the garbage disposal.
4. Get rid of existing placing hardware if equipment substitute needed. Or else miss to step 12.
To get rid of the existing mounting hardware, loosen up the 3 installing screws, pry the snap ring off with a screwdriver and eliminate the old installing setting up.
5. Remove the old sink flange as well as putty.
Press the old sink flange up through the sink opening. Make use of a screwdriver or putty knife to very carefully scratch all old putty from the edge of the sink hole
. Set up the brand-new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drain opening and press it into area. Positioning a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in position while installing the sink flange to the sink. To stay clear of scratching your sink or the flange, put a towel between the sink surface and the weight. From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these items in place.
7. Eliminate the dish washer knockout plug.
If making use of a dishwashing machine, you will require to touch out the dish washer knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver and also hammer to tap it out. Next, eliminate the loose knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired System:
Turn the garbage disposal over and remove electrical cover plate. Pull out cables. Place cable connector (not consisted of) and also run electrical wire via accessibility opening on base of garbage disposal. Tighten up wire port. Press cables right into garbage disposal (do not displace cardboard guard) and replace electrical cover plate.
If you have a hardwired system and also you’re looking to connect a cable, you will certainly require a power cable set.
Corded System:
For a garbage disposal with a factory-installed cable, just plug in to the electrical outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the reduced mounting ring until all 3 tabs are locked right into the placing setting up. The garbage disposal will certainly currently hang by itself.
10. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain trap.
Rotate the garbage disposal so that the discharge tube is lined up with the drainpipe catch. If the discharge tube is as well long, cut off as much as necessary. If it is as well brief, you can buy an extension.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwasher, it might be attached with an air space. Utilize a hose pipe clamp to attach the drainpipe tube to the dishwasher inlet. Since everything is mounted and also ready, lock the garbage disposal to the sink mounting assembly making use of the wrenchette that featured the system. For Evolution models, place the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink till it snaps right into location.
13. Evaluate the garbage disposal.
For all designs, you need to evaluate for leakages at the sink flange, dishwashing machine, tail-pipe and mounting setting up links. Ultimately, activate the electric breaker to evaluate its operation.
Garbage Disposal Installation in Sylmar
Installing a New Garbage Disposal in Sylmar