05 Feb. 21
Mounting a Substitute Garbage Disposal in North Hills
1. Shut off power to the garbage disposal as well as separate the down catch.
Shut off the electric power at the circuit box or breaker. Then, utilizing flexible pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and insert completion of the wrenchette or screwdriver into the best side of one placing lug on the lower mounting ring. Raise the garbage disposal a little and also loosen up the reduced placing ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting setting up.
3. Disconnect the electric.
Lay the garbage disposal on its side and also remove the electric cover plate from the bottom. Loosen up the eco-friendly ground screw and also eliminate wire adapters. Disconnect garbage disposal cables from electrical supply wires. Loosen up screws on the electrical clamp connector and also get rid of wires from the garbage disposal.
4. Remove existing mounting equipment if equipment substitute required. Or else skip to step 12.
To eliminate the existing mounting equipment, loosen the 3 installing screws, tear the breeze ring off with a screwdriver and eliminate the old mounting assembly.
5. Eliminate the old sink flange and putty.
Push the old sink flange up through the sink hole. Make use of a screwdriver or putty blade to thoroughly scratch all old putty from the edge of the sink opening
. Install the brand-new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange into the drain opening and also press it right into place. Positioning a weight, such as the garbage disposal, in addition to the sink flange will aid hold the sink flange in place while mounting the sink flange to the sink. To avoid scraping your sink or the flange, position a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these items in position.
7. Eliminate the dish washer knockout plug.
If using a dish washer, you will certainly need to touch out the dish washer knockout plug. Lay the garbage disposal on its side and also utilize a screwdriver as well as hammer to tap it out. Next off, eliminate the loose ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Device:
Transform the garbage disposal over and also get rid of electrical cover plate. Pull out cords. Insert cable connector (not included) and run electric wire through accessibility opening on base of garbage disposal. Tighten cord connector. Press cords right into garbage disposal (do not displace cardboard guard) and change electric cover plate.
If you have a hardwired unit and also you’re aiming to affix a cord, you will require a power cable set.
Corded System:
For a garbage disposal with a factory-installed cable, simply plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the reduced mounting ring till all three tabs are secured into the installing setting up. The garbage disposal will certainly now hang by itself.
10. Place the discharge tube.
Put the discharge tube into the discharge coupler, then slide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Turn the garbage disposal to ensure that the discharge tube is aligned with the drainpipe trap. If the discharge tube is too long, cut off as much as essential. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwasher, it might be connected via an air void. Make use of a pipe clamp to affix the drain hose pipe to the dish washer inlet. Since whatever is set up and in position, lock the garbage disposal to the sink mounting assembly utilizing the wrenchette that came with the system. For Evolution models, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink till it snaps right into place.
13. Test the garbage disposal.
For all versions, you need to examine for leaks at the sink flange, dishwashing machine, tail-pipe and placing setting up links. Lastly, switch on the electric breaker to evaluate its operation.
How to Install a Garbage Disposal in North Hills
Installing a New Garbage Disposal in North Hills