05 Feb. 21
Mounting a Substitute Garbage Disposal in Woodland Hills
1. Shut off power to the garbage disposal and also detach the down trap.
Switch off the electric power at the fuse box or circuit breaker. Then, using adjustable pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Support the garbage disposal with one hand and insert the end of the wrenchette or screwdriver into the appropriate side of one mounting lug on the reduced placing ring. Lift the garbage disposal somewhat and loosen up the lower mounting ring by pressing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is free from the installing assembly.
3. Detach the electric.
Lay the garbage disposal on its side as well as eliminate the electric cover plate from the bottom. Loosen up the green ground screw and also eliminate cord ports. Detach garbage disposal cords from electric supply wires. Loosen up screws on the electrical clamp adapter and also remove cords from the garbage disposal.
4. Eliminate existing mounting equipment if equipment replacement needed. Otherwise avoid to tip 12.
To eliminate the existing mounting equipment, loosen the three installing screws, pry the snap ring off with a screwdriver and also remove the old mounting assembly.
5. Get rid of the old sink flange and putty.
Press the old sink flange up with the sink hole. Use a screwdriver or putty knife to meticulously scratch all old putty from the side of the sink opening
. Mount the brand-new sink flange, gasket and also rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange into the drainpipe opening and also press it into area. Putting a weight, such as the garbage disposal, on top of the sink flange will assist hold the sink flange in place while placing the sink flange to the sink. To avoid scraping your sink or the flange, place a towel in between the sink surface area as well as the weight. From under the sink, slide the fiber gasket, back-up flange and also placing flange over the sink flange. Hold these items in place.
7. Get rid of the dishwasher ko plug.
If making use of a dishwasher, you will need to touch out the dishwashing machine knockout plug. Lay the garbage disposal on its side and also use a screwdriver and also hammer to tap it out. Next off, get rid of the loosened knockout plug from inside the garbage disposal.
8. Link the electrical.
Hardwired Device:
Transform the garbage disposal over as well as get rid of electric cover plate. Pull out cords. Place wire adapter (not included) and also run electrical cord through gain access to hole on base of garbage disposal. Tighten up wire connector. Press cables right into garbage disposal (do not displace cardboard guard) as well as change electric cover plate.
If you have a hardwired device and also you’re looking to attach a cord, you will need a power cord kit.
Corded Unit:
For a garbage disposal with a factory-installed cord, merely plug in to the electrical outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the lower installing ring until all three tabs are locked into the mounting setting up. The garbage disposal will currently hang by itself.
10. Insert the discharge tube.
Place the discharge tube into the discharge coupler, after that glide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Turn the garbage disposal to ensure that the discharge tube is straightened with the drain trap. If the discharge tube is too long, removed as much as necessary. If it is also brief, you can purchase an expansion.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwasher, it might be linked via an air space. Make use of a pipe clamp to connect the drainpipe tube to the dishwasher inlet. Now that whatever is mounted and ready, lock the garbage disposal to the sink installing setting up using the wrenchette that came with the unit. For Advancement designs, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink up until it breaks right into location.
13. Examine the garbage disposal.
For all models, you ought to evaluate for leakages at the sink flange, dish washer, tail-pipe and also placing assembly connections. Lastly, turn on the electrical breaker to examine its operation.
Whatever You Need to Find Out About Rubbish Disposals in Woodland Hills
How to Choose a Garbage Disposal in Woodland Hills