05 Feb. 21

Setting Up a Replacement Garbage Disposal in Granada Hills

1. Switch off power to the garbage disposal as well as detach the down catch.
Shut off the electric power at the fuse box or breaker. After that, making use of adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the placing assembly.
Support the garbage disposal with one hand and also put the end of the wrenchette or screwdriver into the best side of one installing lug on the reduced installing ring. Lift the garbage disposal a little and loosen up the lower installing ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is without the mounting setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side and remove the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw as well as remove wire adapters. Detach garbage disposal cables from electric supply cables. Loosen screws on the electric clamp port and eliminate cables from the garbage disposal.

4. Get rid of existing mounting hardware if hardware replacement required. Otherwise miss to tip 12.
To remove the existing placing equipment, loosen up the 3 mounting screws, tear the breeze ring off with a screwdriver and also remove the old installing assembly.

5. Eliminate the old sink flange and putty.
Press the old sink flange up via the sink opening. Make use of a screwdriver or putty knife to thoroughly scratch all old putty from the side of the sink hole
. Install the new sink flange, gasket and rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drain opening and press it right into area. Positioning a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while placing the sink flange to the sink. To prevent damaging your sink or the flange, place a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and also installing flange over the sink flange. Hold these pieces in place.

7. Remove the dishwasher ko plug.
If using a dishwasher, you will certainly need to tap out the dishwasher ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver as well as hammer to touch it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
8. Link the electrical.
Hardwired Unit:
Transform the garbage disposal over and also remove electrical cover plate. Take out cables. Put wire adapter (not included) and run electrical wire through accessibility opening on bottom of garbage disposal. Tighten up cable television port. Push cords right into garbage disposal (do not displace cardboard shield) and replace electric cover plate.
If you have a hardwired unit and you’re wanting to attach a cable, you will certainly require a power cord set.
Corded Device:
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the lower installing ring until all three tabs are locked right into the placing assembly. The garbage disposal will certainly now hang on its own.
10. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, then glide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Rotate the garbage disposal to make sure that the discharge tube is aligned with the drainpipe trap. If the discharge tube is also long, cut off as much as necessary. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dish washer, it may be linked through an air void. Use a hose pipe clamp to connect the drainpipe tube to the dishwasher inlet. Since every little thing is set up and ready, secure the garbage disposal to the sink installing assembly making use of the wrenchette that featured the unit. For Evolution models, put the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink till it snaps right into location.

13. Check the garbage disposal.
For all designs, you ought to test for leaks at the sink flange, dishwasher, tail-pipe and also placing assembly links. Ultimately, activate the electric breaker to evaluate its operation.
Installing a New Garbage Disposal in Granada Hills
How to Choose a Garbage Disposal in Granada Hills