05 Feb. 21
Setting Up a Replacement Garbage Disposal in Northridge
1. Turn off power to the garbage disposal as well as separate the down catch.
Turn off the electrical power at the circuit box or breaker. Then, making use of flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand and insert completion of the wrenchette or screwdriver into the right side of one mounting lug on the lower placing ring. Lift the garbage disposal a little and loosen up the lower mounting ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is without the placing assembly.
3. Separate the electrical.
Lay the garbage disposal on its side as well as eliminate the electric cover plate from all-time low. Loosen up the eco-friendly ground screw and remove cable ports. Detach garbage disposal cables from electrical supply wires. Loosen screws on the electrical clamp connector and also get rid of cords from the garbage disposal.
4. Eliminate existing placing equipment if equipment replacement required. Otherwise skip to step 12.
To get rid of the existing mounting hardware, loosen the 3 mounting screws, pry the snap ring off with a screwdriver and eliminate the old installing setting up.
5. Get rid of the old sink flange as well as putty.
Push the old sink flange up through the sink opening. Utilize a screwdriver or putty knife to meticulously scratch all old putty from the side of the sink opening
. Set up the brand-new sink flange, gasket and rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drain opening as well as press it into place. Putting a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in place while placing the sink flange to the sink. To stay clear of scraping your sink or the flange, position a towel in between the sink surface area and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these items in place.
7. Eliminate the dish washer knockout plug.
If making use of a dishwashing machine, you will need to tap out the dish washer ko plug. Lay the garbage disposal on its side and utilize a screwdriver and also hammer to touch it out. Next, get rid of the loose knockout plug from inside the garbage disposal.
8. Connect the electric.
Hardwired Device:
Turn the garbage disposal over and get rid of electric cover plate. Pull out cables. Put cable television connector (not consisted of) and run electrical cable television through accessibility hole on bottom of garbage disposal. Tighten cord port. Press wires right into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired system and you’re looking to attach a cord, you will certainly need a power cord kit.
Corded Unit:
For a garbage disposal with a factory-installed cable, just connect in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, turn the reduced installing ring up until all 3 tabs are secured right into the placing setting up. The garbage disposal will now hang on its own.
10. Put the discharge tube.
Put the discharge tube right into the discharge coupler, after that move the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Rotate the garbage disposal to ensure that the discharge tube is straightened with the drainpipe catch. If the discharge tube is as well long, removed as high as required. If it is also brief, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwashing machine, it might be linked with an air space. Utilize a hose pipe clamp to attach the drain hose pipe to the dish washer inlet. Since whatever is mounted and in position, lock the garbage disposal to the sink mounting assembly utilizing the wrenchette that came with the unit. For Evolution models, place the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink up until it breaks into location.
13. Evaluate the garbage disposal.
For all versions, you ought to check for leaks at the sink flange, dishwashing machine, tail-pipe as well as placing setting up connections. Lastly, switch on the electric breaker to evaluate its operation.
Garbage Disposal Installation in Northridge
Installing a New Garbage Disposal in Northridge