1. Shut off power to the garbage disposal and also separate the down trap.
Switch off the electrical power at the fuse box or circuit breaker. After that, making use of flexible pliers, detach the drain top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand as well as insert the end of the wrenchette or screwdriver right into the right side of one placing lug on the reduced installing ring. Raise the garbage disposal a little as well as loosen up the lower placing ring by pressing or pulling the wrenchette or screwdriver to the left till the garbage disposal is devoid of the installing assembly.
3. Separate the electric.
Lay the garbage disposal on its side and eliminate the electric cover plate from all-time low. Loosen the eco-friendly ground screw as well as get rid of cord adapters. Disconnect garbage disposal cords from electric supply cords. Loosen up screws on the electrical clamp connector and also get rid of cables from the garbage disposal.

4. Remove existing installing equipment if equipment replacement needed. Or else skip to tip 12.
To eliminate the existing installing hardware, loosen the 3 mounting screws, tear the breeze ring off with a screwdriver as well as eliminate the old mounting setting up.

5. Eliminate the old sink flange and putty.
Press the old sink flange up via the sink opening. Make use of a screwdriver or putty blade to carefully scrape all old putty from the edge of the sink hole
. Install the brand-new sink flange, gasket as well as rings.
Place a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Drop the brand-new sink flange into the drain opening and press it into area. Positioning a weight, such as the garbage disposal, on top of the sink flange will aid hold the sink flange in place while mounting the sink flange to the sink. To prevent damaging your sink or the flange, put a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, back-up flange and mounting flange over the sink flange. Hold these items in position.

7. Get rid of the dishwasher ko plug.
If utilizing a dishwashing machine, you will require to touch out the dishwashing machine knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver and also hammer to touch it out. Next off, remove the loosened ko plug from inside the garbage disposal.
8. Link the electric.
Hardwired Unit:
Turn the garbage disposal over and also eliminate electrical cover plate. Pull out cables. Place cord connector (not included) as well as run electrical cord via accessibility opening on base of garbage disposal. Tighten up wire adapter. Press cords right into garbage disposal (do not displace cardboard guard) and also change electrical cover plate.
If you have a hardwired unit as well as you’re wanting to attach a cable, you will require a power cord package.
Corded Device:
For a garbage disposal with a factory-installed cord, merely plug in to the outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the reduced placing ring up until all 3 tabs are secured right into the installing assembly. The garbage disposal will now hang on its own.
10. Put the discharge tube.
Place the discharge tube into the discharge coupler, after that move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe catch.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is as well long, cut off as high as necessary. If it is too short, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dish washer, it may be attached with an air space. Utilize a tube clamp to attach the drainpipe pipe to the dishwashing machine inlet. Now that every little thing is installed as well as in position, secure the garbage disposal to the sink mounting assembly utilizing the wrenchette that featured the device. For Evolution versions, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink until it snaps into area.

13. Check the garbage disposal.
For all models, you ought to examine for leakages at the sink flange, dish washer, tail-pipe and also installing assembly connections. Finally, turn on the electric breaker to check its operation.
How to Install a Garbage Disposal in Sunland-Tujunga
Whatever You Need to Learn About Trash Disposals in Sunland-Tujunga